Filter
Second filter
Third filter
Fourth filter

GPRS & GSM & GPS

In this category there are modules and antennas for GPRS, GSM and GPS communication. For example GNSS GPS L86-M33 breakout or GSM/GPRS SIM800L module.

Showing all 9 results

Sort by:
GNSS GPS L86-M33 breakout with easyC
GNSS GPS L86-M33 breakout with easyC

Global Navigation Satellite Signal Systems (GNSS), or as we all like to call it “GPS”, enable precise location determination on Earth. Thanks to this module, you can use GNSS for your project and use the device for asset tracking or create a wearable device. The module is small, energy-efficient, high-performing, and easy to use thanks to the built-in antenna.

 

 

L86-M33 is a GNSS receiver, which means it can receive signals from GPS, GLONASS, and Galileo constellations. Equipped with EASY (Embedded Assist System for self-generated orbit prediction) and AlwaysLocate technologies, L86-M33 ensures fast and accurate positioning even in challenging environments. Its advanced internal logger LOCUS allows you to store your routes and location data.

 

 

Our breakout board, in addition to the previously mentioned L86-M33 module which has an integrated antenna, also has a connector for a CR1220 battery which is used as a backup for timekeeping and GPS data. The module can operate without the battery, but every time it will have to fetch data from satellites afresh (cold start). If the integrated antenna is insufficient, there is an IPX connector on the board for adding an external, stronger antenna. The antenna we suggest can be found here. To easily access the module pins, the pins are extended on the board for accessibility. There is also a switch on the board to change the I2C address.

GNSS GPS L86-M33 breakout
GNSS GPS L86-M33 breakout

Global Navigation Satellite Systems (GNSS), or as we all like to call it “GPS,” enable precise location determination on Earth. Thanks to this module, you can use GNSS for your project and employ the device for asset tracking or create a wearable device. The module is small, energy-efficient, highly effective, and easy to use thanks to its built-in antenna.

 

L86-M33 is a GNSS receiver, meaning it can receive signals from GPS, GLONASS, and Galileo constellations. Equipped with EASY (Embedded Assist System for self-generated orbit prediction) and AlwaysLocate technologies, the L86-M33 ensures fast and accurate positioning even in challenging environments. Its advanced internal logger, LOCUS, allows you to store your routes and location data.

 

In addition to the aforementioned L86-M33 module, which has an integrated antenna, our breakout board also has a connector for a CR1220 battery that is used as a backup for timekeeping and GPS data. The module can operate without a battery, but each time it will have to pull data from the satellites anew (cold start). If the integrated antenna is not sufficient, there is an IPX connector on the board for adding an external, stronger antenna. You can find the antenna we recommend here. To easily access the pins of the module, the pins are exposed on the board for easy access.

Out of stock IPX to SMA-F cable
IPX to SMA-F cable

IPX to SMA female cable will allow you easy connection with SMA male antenna to IPX connector which is, for example, a common case with a GSM antenna.

GSM/GPRS module SIM800L
GSM/GPRS module SIM800L

SIM800 is a well-known chip for GSM / GPRS (2G mobile network) communication. Insert a SIM card, call, send SMS and connect to the Internet using a microcontroller. This breakout allows these connections in a simple way, it communicates with Arduino over a serial link. It is programmed using Arduino’s already finished libraries. Breakout even comes with a small wire antenna that will be sufficient for testing and use in areas where the signal is corresponding!

 

Active GPS antenna, SMA connector
Active GPS antenna, SMA connector

The active GPS antenna allows you to get a better GPS signal reception to your device. The antenna comes with a 3m cable at the end of which is the classic SMA male connector. There is a magnet for easier installation at the bottom of the antenna.

 

• Connector: SMA male
Frequency: 1575.42MHz
• Voltage: 3V-5V
• Current: 10mA max.
• Polarization: circular(RH)
• Amplification: 28dB
• Dimensions: 45mm x 39mm x 13mm

GSM PCB antenna with IPX connector
GSM PCB antenna with IPX connector

GSM PCB antenna with IPX connector for connection on your boards that use an IPX connector.

4G/LTE PCB antenna with IPX connector
4G/LTE PCB antenna with IPX connector

This antenna connects you to 4G/LTE network it connects on your device via an IPX connector.

 

• Frequency: 4GHz/LTE
Dimensions: 40 x 15 x 0.25mm
• Cable lenght: 12cm

VK172 USB GPS module
VK172 USB GPS module

This U-blox7 GPS / GLONASS module connects to USB and can be used to obtain GPS coordinates.

To use this module, drivers from the official website must be installed.

Ceramic GPS antenna 1575.42MHz with IPX connector
Ceramic GPS antenna 1575.42MHz with IPX connector

The ceramic antenna at a frequency of 1575.42MHz corresponding GPS. Ideal with our SIM808 breakout.

 

items per page