Filter
Second filter
Third filter
Fourth filter

Soldering

Here you will find everything for soldering from our offer. Products like flux, various colored prototyping wires, soldering irons, prototyping boards, etc.

Showing 1–24 of 35 results

Sort by:
Heatshrink set
Heatshrink set

A set of heat shrinks that insulate the connections between the wires when heated.

 

The set consists of:

  • • 60 heat shrinks 40 mm long, 2 mm in diameter
  • • 30 heat shrinks 40 mm long, 3 mm in diameter
  • • 16 heat shrinks 40 mm long, 4 mm in diameter
  • • 16 heat shrinks 40 mm long, 5 mm in diameter
  • • 16 heat shrinks 40 mm long, 6 mm in diameter
  • • 10 heat shrinks 40 mm long, 9 mm in diameter
  • • 8 heat shrinks 40 mm long, 10 mm in diameter
  • • 8 heat shrinks 40 mm long, 11 mm in diameter
Prototyping wire 10m, red, AWG25
Prototyping wire 10m, red, AWG25

It is extremely easy to remove insulation and solder with this stranded copper wire. It will serve great in small projects and prototypes.

Soldering iron 40W
Soldering iron 40W

The soldering iron is an essential tool for anyone who does something with electronics. Although we enjoy using more expensive soldering irons, this one is affordable and does the job – it will come in handy as a first or spare soldering iron, and with its price, it is affordable to everyone. The process of soldering permanently connects two pieces of metal. In electronics it is the joints between wires, components and boards. Whatever you want to do, you’ll always need to solder something, especially if you’re going to fix electronics – you must have a soldering iron. This soldering iron has a power of 40W, which is quite enough for soldering and desoldering in most cases.

Out of stock Solder Sn99,3Cu0,7 1mm
Solder Sn99,3Cu0,7 1mm

Classic solder for working with a hand soldering iron. Solder paste is in the center of the solder, which simultaneously cleans the surface on which its soldering and gives a better grip of solder.

Cleaning net for soldering iron
Cleaning net for soldering iron

If the soldering iron isn’t clean, neither will the the solder joint. This cleaning net allows quick tip cleaning by “stabbing” the soldering iron in it. When the net is filled with solder, simply remove it from the casing, clean the excess solder, return it back and use it again!

PCB breadboard/protoboard
PCB breadboard/protoboard

This PCB is also a protoboard. It offers both the simplicity and the functionality of a breadboard. It is the same size as the modular half-size breadboard and has the same connections to pins. The board allows you to make the temporary circuit from the breadboard permanent.

 

Product usage tips:

 

The board has three mounting holes for secure placement on different surfaces.

 

Desoldering wick, high-quality 1.9mm
Desoldering wick, high-quality 1.9mm

Desoldering wick is a very practical tool for every workshop. It’s a braided copper wire, soaked in flux, so it catches solder effectively. If you have a spot from which you need to remove the solder, this strip will do a great job. Unlike the discharge pump, this strip can completely remove the solder from a hole or a pad. 1.5m should last long since you spend only one or two centimeters per one desoldering.

 

Lenght: 1.5m
Width: 1.9mm

Liquid flux, RF800, 100mL
Liquid flux, RF800, 100mL

Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. This liquid solder is applied with a brush to the solder spots on the tile.

 

• Quantity: 100mL
• Density: 0,794g/cm3
• Soluble in water

 

REMARK: Be sure to close the flux after use.

Activated flux 40g
Activated flux 40g

Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. In addition to all the above, this flux contains activators that further improve soldering, to the point that soldering is as simple and high quality as with solder paste.

 

• Weight: 40g

 

REMARK: Be sure to close the flux after use.

Protoboard 2x8cm
Protoboard 2x8cm

Well known protoboard 2 x 8 cm. Can be used for all of the ongoing mergers and soldering. Very good quality.

Prototyping wire 10m, black, AWG25
Prototyping wire 10m, black, AWG25

It is extremely easy to remove insulation and solder with this stranded copper wire. It will serve great in small projects and prototypes.

Soldering iron stand
Soldering iron stand

Since the soldering iron is hot during operation, it is necessary to have a safe place to store it. This stand is affordable and serves its purpose. It also contains a sponge in its base on which it is possible to clean the tip of the soldering iron.

Desoldering wick 2mm
Desoldering wick 2mm

The desoldering wick is a very practical aid during soldering. It is an interwoven copper wire soaked in flux to catch the solder. If you have a spot where you need to remove the solder, this tape will do a great job. Unlike the desoldering pump, this tape can completely remove the solder from the hole or from the pad.

 

Length: 1.5m
Width: 2.0mm

Flux paste for soldering 40g
Flux paste for soldering 40g

Where do we use flux? Flux is used by soldering. It is used to clean the pcb from any dust or oxidation (if there was any), which results with quality solder connections – solder attaches more easily to the pads where we want to put solder. Besides that, it improves electrical contact. Anyone who has tried it will know!

 

• Amount: 40g

 

Warning: Close the flux can after use.

Solder Sn60Pb40 1.0mm 50g
Solder Sn60Pb40 1.0mm 50g

Classic solder for working with a hand soldering iron. In the center of the solder is a solder paste that simultaneously cleans the surface on which it is soldered and allows better adhesion of the solder. This solder is the so-called leaded.

 

Quantity: 50g
Diameter: 1.0mm
• Composition: Sn60Pb40

Mini PCB breadboard/protoboard
Mini PCB breadboard/protoboard

A 2-in-1 breadboard and PCB is what you get when combining the simplicity of the one and functionality of the other. It is the same size as the modular mini breadboard and has the same connections to pins. This PCB lets you move your circuit from a temporary connection on a classic breadboard to a more permanent place by soldering all the pieces.

 

Product usage tips:

The board can be secured in place by using the two mounting holes in the middle.

Protoboard 15x9cm
Protoboard 15x9cm

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.

 

• Dimensions: 15cm x 9cm

Protoboard 12x8cm
Protoboard 12x8cm

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on both sides, as well as column and row markings.

 

Protoboard 7x9cm
Protoboard 7x9cm

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.

 

• Dimensions: 7cm x 9cm

Protoboard 6x4cm
Protoboard 6x4cm

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.

 

• Dimensions: 6cm x 4cm

Kapton tape 30mm
Kapton tape 30mm

Kapton is a special type of material that is resistant to high temperatures and does not conduct electricity. When it is thinly rolled out and adhesive tape is placed on it, we get a kapton tape. In electronics, it is often used to protect plastic components from damage during soldering and as an insulator.

 

• Tape width: 30mm
• Tape length: 10m

 

Liquid flux, RF800, 15mL
Liquid flux, RF800, 15mL

Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. This liquid solder is applied with a brush to the solder spots on the tile.

 

• Quantity: 15mL
• Density: 0,794g/cm3
• Soluble in water

 

REMARK: Be sure to close the flux after use.

Electrical tape 30m
Electrical tape 30m

Electrical tape is well known to everyone – it provides insulation between various connections. This is an extra-large, 30m roll. The color you receive will be randomly selected.

Out of stock Lead-free solder paste Sn96,5Ag2Cu0,5 1.4mL
Lead-free solder paste Sn96,5Ag2Cu0,5 1.4mL

Solder paste is used during SMT production, i.e. when SMT components are used. The paste is placed in specific places where it’s desired to achieve a solder joint, either by hand or with a stencil. After that, the components are placed and soldered in special ovens. This paste does not require cleaning after soldering (no clean). Paste is lead-free, which means it does not contain lead.

 

Composition: Sn96,5Ag3Cu0,5
Melting point: 252°C
Solder ball sizes: 25-45µm
Packaging: 1.4mL
Lead-free
No clean

 

At e-radionica.com solder paste is stored in the refrigerator, at a temperature of 8 ° C, which is the recommended storage temperature. We recommend that you choose express delivery for orders that contain this item in order to avoid product being exposed to high temperatures.

items per page